EN
Better quality
Better QualityBetter service
Better Quality
The Largest Manufacturer of MTHPA Products in China.

Introduction to Preparation of Methyl Tetrahydrophenylanhydride

Methyltetrahydrophthalic anhydride plays a very important role in the medical, pesticide and other industries. I believe that many people don't know much about methyltetrahydrophthalic anhydride. Today, I will mainly introduce the knowledge of methyltetrahydrophthalic anhydride preparation.


To synthesize methyl tetrahydrophthalic anhydride with gaseous mixture of C5 and maleic anhydride in methyl tetrahydrophthalic anhydride solution:


1) Experimental method of batch reaction


Prepare a certain amount of 25% maleic anhydride in methyltetrahydrophthalic anhydride solution, add an appropriate amount of polymerization inhibitor, take 80mL of the prepared solution and add it to the maleic anhydride solution storage bottle, and take 41mL of mixed C5 liquid into the C5 storage bottle (The ratio of the active component in C5 to the amount of maleic anhydride is 1.1:1), keep the constant temperature water tank at 44℃ (the boiling point of C5 at normal temperature), and control the dropping rate of C5 by adjusting the knob. The rate of ld/3s, ld/4S and ld/5S is added dropwise. C5 is added dropwise to the gasification flask to quickly vaporize and flow into the reaction flask to react with maleic anhydride solution (the C5 gas velocity is measured by liquid volume). Investigate the effect of c5 feed rate and temperature on the reaction. Record the temperature in the reaction flask every 15 minutes after the start of the experiment, and take samples for analysis.


2) Continuous reaction experiment method


Prepare a certain amount of 25% maleic anhydride in methyltetrahydrophthalic anhydride solution, add an appropriate amount of polymerization inhibitor, add the prepared maleic anhydride solution to the storage bottle, and take a sufficient amount of mixed C5 liquid into the C5 storage bottle. The constant temperature water bath where the C5 vaporization bottle is located is kept at 44℃, and the dropping speed of C5 and maleic anhydride is controlled by adjusting the knob to investigate the influence of the feed ratio on the reaction. Change the temperature of No. 1 constant temperature water bath to investigate the influence of temperature. After the experiment starts, record the temperature in the reaction flask every 15 minutes and take samples for analysis.

Related News
  • How to Choose a Curing Agent

    How to Choose a Curing Agent

    August 26, 2020(1) Consider the varieties and performance of the curing agentThe varieties of curing agent have a great influence on the mechanical properties, heat resistance, water resistance, corrosion resistance...view
  • Heat Resistant Epoxy Glue

    Heat Resistant Epoxy Glue

    March 16, 2020Ordinary epoxy adhesive can only withstand 80℃ or 120℃. This epoxy adhesive is generally a bisphenol A epoxy resin type. The modified epoxy adhesive can reach 350-400℃ in a short time and 200-300℃...view
  • What Do You Know about Methyltetrahydrophthalic Anhydride

    What Do You Know about Methyltetrahydrophthalic Anhydride

    January 25, 2021I don't know if you are familiar with methyltetrahydrophthalic anhydride. In fact, some people are not too familiar with it. In fact, what many people have always wondered is what are the function...view
  • Key Points of Formulation Design of the Heat Resistant Epoxy Glue

    Key Points of Formulation Design of the Heat Resistant Epoxy Glue

    May 26, 2020Main factors affecting the temperature resistance of epoxy adhesiveThe high temperature property of epoxy adhesive depends on the thermal deformation temperature and thermal oxidation stability of the...view
  • How to Use the Heat Resistant Epoxy Glue

    How to Use the Heat Resistant Epoxy Glue

    May 26, 2020Epoxy glue, also known as instant dry glue or instant dry glue, is 502 in the general market. Instant dry adhesive can fix many temporary objects. Why is it temporary? Because instant dry glue is not ...view
  • Class 1- Resin Hardener

    Class 1- Resin Hardener

    March 16, 2020Epoxy resin curing agent is an additive that reacts with epoxy resin to form a reticular three-dimensional polymer, envelops composite material in a reticular body, and makes the linear resin into a t...view


Contact Us